CONDITION SETTINGS

If you print data in an environment where the printer driver is not used (that is, if you print data using the MS-DOS system or if you print data using the PC that does not have the provided printer driver installed), set the detailed printing conditions. (However, the "Disable Blank Page Print" function will be effective even when the PCL printer driver is used.)
When printing using the printer driver, the printer driver settings take precedence over the printer condition settings.
Settings
Item Setting
Copies 1 - 9999 sets
Orientation
  • Portrait
  • Horizontal
Default Paper Size 8-1/2" x 14", 8-1/2" x 13-2/5" (216 mm x 340 mm), 216 mm x 330 mm (8-1/2" x 13"), 216 mm x 343 mm (8-1/2" x 13-1/2"), 8-1/2" x 11", 7-1/4" x 10-1/2", 5-1/2" x 8-1/2", A3W, A3, B4, A4, B5, A5, 12" x 18", 11" x 17", 8K, 16K
Default Output Tray
  • Center Tray (Not displayed if a finisher is installed)
  • Finisher Upper Tray*1
  • Finisher Lower Tray*1
  • Right Tray
Default Paper Type Plain Paper, Letter Head, Pre-Printed, Pre-Punched, Recycle Paper, Color
Initial Resolution Settings
  • 600 dpi
  • 600 dpi (High Quality)
  • 1200 dpi
Disable Blank Page Print
  • (Enabled)
  • (Disabled)
Line Thickness*2 0 to 9
2-Sided Print
  • 1-Sided
  • 2-Sided (Booklet)
  • 2-Sided (Tablet)
N-Up Print*3 N-Up
  • 1-Up
  • 2-Up
  • 4-Up
  • 8-Up
Layout
  • Left To Right*4
  • Right To Left*4
  • Upper-Left To Right*5
  • Upper-Left To Lower*5
  • Upper-Right To Left*5
  • Upper-Right To Lower*5
Fit To Page*6
  • (Use Fit to Page)
  • (Do not use Fit to Page)
OUTPUT
  • (Use Print per Unit)
  • (Do not use Print per Unit)
  • (Insert Before Job)
  • Paper tray: Trays 1 to 5, bypass tray, inserter (upper/lower)
  • (Do not Insert Before Job)
  • (Insert After Job)
  • Paper tray: Trays 1 to 5, bypass tray, inserter (upper/lower)
  • (Do not Insert After Job)
  • Staple Position: None, 1 Staple at Back, 2 Staples, 2 Staples (Top)
  • (Slant Staple)*1
  • (Do not Slant Staple)*1
  • (Use Punch)
  • (Do not use Punch)
Fold
  • Enabled
  • Disabled
Saddle Fold
Z-Fold
C-Fold
Accordion Fold
Double Fold
Half Fold
Trimming Width Settings 2.0 to 20.0 mm
Quick File
  • (Disabled)
  • (Enabled)
*1
When the saddle finisher or finisher is installed
*2
This setting is used to adjust the line width of vector graphics. Except for CAD and other specialized uses, there is normally no need to change this setting. When "0" is selected, all lines are printed at a width of 1 dot.
*3
Paper sizes that can be used with this function are 11" x 17", 8-1/2" x 14", 8-1/2" x 11", A3, B4, and A4. (This function may not take effect with some print methods.)
*4
Can be selected when 2-Up is selected.
*5
Can be selected when 4-Up/8-Up is selected.
*6
Only effective when printing PDF, JPEG, and TIFF files.
*7
When a punch module is installed
Back to top